Hi,
I have a HP Microserver Gen 10 (AMD Opteron(tm) X3421 APU) freshly installed with Debian bookworm (6.1.0-21-amd64 /Debian 6.1.90-1 (2024-05-03) x86_64) with 4x WD RED SATA 6TB Disks and one WD Blue 250GB SATA SSD
I am entirely unable to interact with the four disks in the front bays, however I can see the disk I'm booting from on the discrete SATA port.
Is there something I'm doing wrong here?
I have verified as far as I can that the disks are JBOD, healthy (SMART) and usable in TrueNAS, however in Linux I'm unable to list them or interact with them at all.
Grateful for any advice.
M.
I have a HP Microserver Gen 10 (AMD Opteron(tm) X3421 APU) freshly installed with Debian bookworm (6.1.0-21-amd64 /Debian 6.1.90-1 (2024-05-03) x86_64) with 4x WD RED SATA 6TB Disks and one WD Blue 250GB SATA SSD
I am entirely unable to interact with the four disks in the front bays, however I can see the disk I'm booting from on the discrete SATA port.
- - I have put them in JBOD in the controller:
(01:00.0 SATA controller: Marvell Technology Group Ltd. 88SE9230 PCIe 2.0 x2 4-port SATA 6 Gb/s RAID Controller (rev 11)
- I see all the disks in BIOS and in the F11 "Boot menu"
- Disks accessible without fault when using TrueNAS (BSD)
Code:
[ 2.435457] scsi host1: ahci[ 2.435981] scsi host2: ahci[ 2.436363] scsi host3: ahci[ 2.436623] usb: port power management may be unreliable[ 2.437047] scsi host4: ahci[ 2.437608] scsi host5: ahci[ 2.438027] scsi host6: ahci[ 2.438403] scsi host7: ahci[ 2.438797] scsi host8: ahci[ 2.439008] ata2: SATA max UDMA/133 abar m2048@0xfea40000 port 0xfea40100 irq 34[ 2.439073] ata3: SATA max UDMA/133 abar m2048@0xfea40000 port 0xfea40180 irq 34[ 2.439134] ata4: SATA max UDMA/133 abar m2048@0xfea40000 port 0xfea40200 irq 34[ 2.439194] ata5: SATA max UDMA/133 abar m2048@0xfea40000 port 0xfea40280 irq 34[ 2.439253] ata6: SATA max UDMA/133 abar m2048@0xfea40000 port 0xfea40300 irq 34[ 2.439318] ata7: SATA max UDMA/133 abar m2048@0xfea40000 port 0xfea40380 irq 34[ 2.439378] ata8: SATA max UDMA/133 abar m2048@0xfea40000 port 0xfea40400 irq 34[ 2.439437] ata9: SATA max UDMA/133 abar m2048@0xfea40000 port 0xfea40480 irq 34[ 2.467995] tg3 0000:02:00.1 enp2s0f1: renamed from eth1[ 2.507963] tg3 0000:02:00.0 enp2s0f0: renamed from eth0[ 2.683860] usb 1-1: new high-speed USB device number 2 using ehci-pci[ 2.756502] ata2: SATA link up 6.0 Gbps (SStatus 133 SControl 300)[ 2.756625] ata7: SATA link down (SStatus 0 SControl 310)[ 2.756732] ata9: SATA link up 1.5 Gbps (SStatus 113 SControl 300)[ 2.756821] ata6: SATA link down (SStatus 0 SControl 310)[ 2.756900] ata8: SATA link down (SStatus 0 SControl 310)[ 2.840419] usb 1-1: New USB device found, idVendor=0438, idProduct=7900, bcdDevice= 0.18[ 2.840492] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0[ 2.842082] hub 1-1:1.0: USB hub found[ 2.843049] hub 1-1:1.0: 4 ports detected[ 2.895894] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)[ 2.897948] ata1.00: ATA-9: WDC WDS250G1B0A-00H9H0, X41100WD, max UDMA/133[ 2.898067] ata1.00: 488397168 sectors, multi 1: LBA48 NCQ (depth 32), AA[ 2.898775] ata1.00: Features: Dev-Sleep[ 2.901601] ata1.00: configured for UDMA/133[ 2.902112] scsi 0:0:0:0: Direct-Access ATA WDC WDS250G1B0A- 00WD PQ: 0 ANSI: 5[ 2.935875] ata3: SATA link up 6.0 Gbps (SStatus 133 SControl 300)[ 3.115885] ata4: SATA link up 6.0 Gbps (SStatus 133 SControl 300)[ 3.131869] usb 1-1.3: new low-speed USB device number 3 using ehci-pci[ 3.246378] usb 1-1.3: New USB device found, idVendor=045e, idProduct=07f8, bcdDevice= 3.00[ 3.246449] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=0[ 3.246502] usb 1-1.3: Product: Wired Keyboard 600[ 3.246546] usb 1-1.3: Manufacturer: Microsoft[ 3.327878] usb 1-1.4: new low-speed USB device number 4 using ehci-pci[ 3.331077] ata9.00: ATAPI: MARVELL VIRTUAL, 1.09, max UDMA/66[ 3.331230] ahci 0000:01:00.0: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x0002 address=0xdff7d840 flags=0x0050][ 3.355883] ata5: SATA link up 6.0 Gbps (SStatus 133 SControl 300)[ 3.440211] usb 1-1.4: New USB device found, idVendor=0001, idProduct=0000, bcdDevice= 1.00[ 3.440285] usb 1-1.4: New USB device strings: Mfr=0, Product=1, SerialNumber=0[ 3.440342] usb 1-1.4: Product: MEC0003[ 7.831925] ata2.00: qc timeout after 5000 msecs (cmd 0xec)[ 8.087905] ata3.00: qc timeout after 5000 msecs (cmd 0xec)[ 8.332622] ata2.00: failed to IDENTIFY (I/O error, err_mask=0x4)[ 8.343863] ata4.00: qc timeout after 5000 msecs (cmd 0xec)[ 8.587874] ata3.00: failed to IDENTIFY (I/O error, err_mask=0x4)[ 8.599898] ata5.00: qc timeout after 5000 msecs (cmd 0xec)[ 8.599976] ata5.00: failed to IDENTIFY (I/O error, err_mask=0x4)[ 8.844084] ata4.00: failed to IDENTIFY (I/O error, err_mask=0x4)[ 8.916128] ata5: SATA link up 6.0 Gbps (SStatus 133 SControl 300)[ 9.148215] ata2: SATA link up 6.0 Gbps (SStatus 133 SControl 300)[ 9.404536] ata3: SATA link up 6.0 Gbps (SStatus 133 SControl 300)[ 9.660513] ata4: SATA link up 6.0 Gbps (SStatus 133 SControl 300)[ 18.583962] ata9.00: qc timeout after 15000 msecs (cmd 0xef)[ 19.083977] ata9.00: failed to set xfermode (err_mask=0x4)[ 19.095849] ata5.00: qc timeout after 10000 msecs (cmd 0xec)[ 19.095924] ata5.00: failed to IDENTIFY (I/O error, err_mask=0x4)[ 19.095992] ata5: limiting SATA link speed to 3.0 Gbps[ 19.351860] ata2.00: qc timeout after 10000 msecs (cmd 0xec)[ 19.412472] ata5: SATA link up 6.0 Gbps (SStatus 133 SControl 320)[ 19.607848] ata3.00: qc timeout after 10000 msecs (cmd 0xec)[ 19.852634] ata2.00: failed to IDENTIFY (I/O error, err_mask=0x4)[ 19.852709] ata2: limiting SATA link speed to 3.0 Gbps[ 19.863864] ata4.00: qc timeout after 10000 msecs (cmd 0xec)[ 19.900158] ata9: SATA link up 1.5 Gbps (SStatus 113 SControl 300)[ 20.108601] ata3.00: failed to IDENTIFY (I/O error, err_mask=0x4)[ 20.108677] ata3: limiting SATA link speed to 3.0 Gbps[ 20.363904] ata4.00: failed to IDENTIFY (I/O error, err_mask=0x4)[ 20.363980] ata4: limiting SATA link speed to 3.0 Gbps[ 20.668444] ata2: SATA link up 6.0 Gbps (SStatus 133 SControl 320)[ 20.924129] ata3: SATA link up 6.0 Gbps (SStatus 133 SControl 320)[ 21.180562] ata4: SATA link up 6.0 Gbps (SStatus 133 SControl 320)[ 24.983935] ata9.00: qc timeout after 5000 msecs (cmd 0xa1)[ 25.484047] ata9.00: failed to IDENTIFY (I/O error, err_mask=0x4)[ 25.484116] ata9.00: revalidation failed (errno=-5)[ 26.300547] ata9: SATA link up 1.5 Gbps (SStatus 113 SControl 300)[ 36.503933] ata9.00: qc timeout after 10000 msecs (cmd 0xa1)[ 37.003884] ata9.00: failed to IDENTIFY (I/O error, err_mask=0x4)[ 37.003951] ata9.00: revalidation failed (errno=-5)[ 37.004003] ata9.00: disable device[ 38.320543] ata9: SATA link up 1.5 Gbps (SStatus 113 SControl 300)[ 50.327906] ata5.00: qc timeout after 30000 msecs (cmd 0xec)[ 50.327983] ata5.00: failed to IDENTIFY (I/O error, err_mask=0x4)[ 50.644563] ata5: SATA link up 6.0 Gbps (SStatus 133 SControl 320)[ 52.375869] ata4.00: qc timeout after 30000 msecs (cmd 0xec)[ 52.375950] ata3.00: qc timeout after 30000 msecs (cmd 0xec)[ 52.376025] ata2.00: qc timeout after 30000 msecs (cmd 0xec)[ 52.876226] ata4.00: failed to IDENTIFY (I/O error, err_mask=0x4)[ 52.876309] ata3.00: failed to IDENTIFY (I/O error, err_mask=0x4)[ 52.876375] ata2.00: failed to IDENTIFY (I/O error, err_mask=0x4)[ 53.692622] ata2: SATA link up 6.0 Gbps (SStatus 133 SControl 320)[ 53.692726] ata3: SATA link up 6.0 Gbps (SStatus 133 SControl 320)[ 53.692831] ata4: SATA link up 6.0 Gbps (SStatus 133 SControl 320)I have verified as far as I can that the disks are JBOD, healthy (SMART) and usable in TrueNAS, however in Linux I'm unable to list them or interact with them at all.
Grateful for any advice.
M.
Statistics: Posted by afterlife — 2024-05-24 07:54 — Replies 3 — Views 109